Hannspree M19N2 Bedienungsanleitung

MAF-00100219”Liquid Crystal DisplayMonitorM19W2/M19N2

9BEFORE YOU OPERATE THE MONITORFEATURES• 19” screen TFT Color LCD Monitor• Crisp, Clear Display• Recommended Resolutions:19” Wide (16:10) 1440 X 90019

10POWERPOWER SOURCE:1. Make sure that the power cord is the correct type required in your area.2. This LCD monitor has an Internal universal power s

11CONTROLS AND CONNECTORSCABLE CONNECTIONSTurn off your computer before performing the procedure below.1. Connect one end of the 15-pin D-SUB cable t

121 Headphone Jack 2 Audio In3 D-SUB Input 4 HDMI Input5 Power AC InputAudio INAC INHDMID-SUB54321 Figure 1. Connecting Cables

13ADJUSTING THE VIEWING ANGLE• For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your

14OPERATING INSTRUCTIONSGENERAL INSTRUCTIONSPress the power button to turn the monitor on or off. The other control buttons are located at front panel

15FRONT PANEL CONTROL• Power Button:Press this button to switch the monitor on and off.• Power Indicator (LED):Green — Power On modeOrange — Power Sav

16HOW TO ADJUST A SETTINGOSD DescriptionBrightness adjustment:Select the “Brightness” option from the Main Menu. Press MENU key and adjust the level.I

17Horizontal position adjustment:Select the “H-position” option to shift the screen image to the left or right. Press MENU key and adjust the level.Ve

18Video mode:Select the “Video Mode” option to set the image quality when using the HDMI input. Press MENU key to select Normal or Vivid.Backlight Mod

Table of Contents1REGULATORY INFORMATION... 2RECYCLING INFORMATION...

19Change Color Settings for D-SUB source:Move the cursor to one of the preset options and select it.Change Color Settings for D-SUB source:Move the cu

20How to set the OSD:Select “OSD Setting” from the Main Menu, and then press MENU key.OSD horizontal adjustment:Select the “OSD H-Position” option to

21OSD Transparency setting:Select the “OSD Transparency” option to adjust the transparency of the OSD. Press MENU key and adjust the level.OSD color s

22DDC/CI:When DDC/CI is enabled, users are allowed to configure the software monitor settings in Windows Vista. Select the “DDC/CI” option to enable o

23Near Timing Mode:Select the “Near Timing Mode” option to enable or disable this function. Press MENU key to select On or Off.DOS mode:Select the “DO

24PLUG AND PLAY ( Plug & Play DDC2B Feature)This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows th

25TECHNICAL SUPPORT (FAQ)TROUBLE SHOOTINGPROBLEM POSSIBLE SOLUTIONPower LED is not on • Check the power cord.No Plug & Play or screen image is str

26ERROR MESSAGE & POSSIBLE SOLUTION• CABLE NOT CONNECTED :1. Check whether the signal-cable is properly connected. If the connector is loose, tigh

27FACTORY PRESET TIMING TABLE:* The three timing modes are for 19” widescreen support only.TIMING MODEHORIZONTAL FREQUENCY (kHz)VERTICAL FREQUENCY (Hz

28HDMI TIMING TABLE:MODE TIMING RESOLUTION V-FREQ.(Hz)1 VGA/60 Hz 640x480p 59.94/602 720p/60 Hz 1280x720p 59.94/603 1080i/60 Hz 1920x1080i 59.94/604 4

2REGULATORY INFORMATIONBefore operating the monitor, please read this manual thoroughly. This manual should be retained for future reference.FCC Class

29APPENDIXSPECIFICATIONSLCD PanelModel NO. M19W2 M19N2Display size 19"(16:10) 19"(5:4)Pixel Pitch 0.2835(H)x0.2835(V) 0.294(H)x0.294(V)Input

30The above specification is subject to actual panel specification and is subject to change without prior notice.* Applies to specific compliant model

31CONNECTOR PIN ASSIGNMENT• 15-Pin Color Display Signal Cable:• HDMI Color Display Signal Cable: PIN NO. DESCRIPTION PIN NO. DESCRIPTION1Red 9+5V2 Gre

32• 24-Pin Color Display Signal Cable: (Dual Input Mode)7 TMDS Data 0+ 17 CEC/GND8 TMDS Data 0 shield 18 +5V Power9 TMDS Data 0- 19 Hot Plug Detect10

ファックス

3TCO’03 (TCO’03 applied model only)Congratulations!The display you have just purchased carries the TCO’03 Displays label. This means that your display

4RECYCLING INFORMATIONHANNspree Inc. cares about environmental protection strategies and in using manufacturing methods and treatments that lend thems

5SAFETY NOTICE1. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to oper

6• Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a fire or electric shock. Never spill liquids on t

7• Due to the nature of LCD screens, an after image of the previous displayed content may remain if this image has been the displayed for several hour

8PREFACEThank you for purchasing a Hannspree Liquid Crystal Display Monitor (LCD Monitor).Please carefully read this manual in its entirety before set